Conventional Detection
Search for: accessory
|
|
 RA100Z
 Data Sheet (pdf)
 Installation Instructions (pdf)
RA100Z remote annunciator is designed for both conventional and intelligent applications.
|
|
|
F-A3384-000
Replacement Air Filter
|
|
|
P-COUPLING
Coupling
|
|
|
P-ELB-45
45 degree Elbow
|
|
|
P-ELB-90
90 degree Elbow
|
|
|
P-ENDCAP
End Cap
|
|
|
P-LABEL-P
Sampling Point Labels
|
|
|
P-LABEL-T
Pipe Labels
|
|
|
P-PIPE-210
CPVC Pipe
|
|
|
P-TEE
Tee
|
|
|
P-UNION
Union
|
|
|
SENS-RDR
Data Sheet (pdf)
Installation Instructions (pdf)
The SENS-RDR is utilizes infrared technology to read the sensitivity of i3 Series detectors.
|
|
|
2W-MOD2
Data Sheet (pdf)
Installation Instructions (pdf)
 Engineering Specs
The 2W-MOD2 is a two-wire loop test and maintenance module for use with i3 Series detectors. (Replaces Model No. 2W-MOD)
|
|
|
RT
The RT is an installation/removal tool for use with i3 Series detectors.
Detector removal tool guide
|
|
|
RRS-MOD
Data Sheet (pdf)
Installation Instructions (pdf)
Engineering Specs
The RRS-MOD is a reversing relay/synchronization module for use with i3 Series detectors with built-in sounder.
|
|
|
A77-AB
Data Sheet (pdf)
The A77-AB Adapter Bracket allows installers to retrofit applications where a larger diameter detector was previously installed.
|
|
|
A77-AB2
The A77-AB2 allows installers to retrofit i3 Series detectors where a larger diameter detector was previously installed.
|
|
|
MOD400R
Data Sheet (pdf)
Installation Instructions (pdf)
The MOD400R is used to check the sensitivity of System Sensor 100, 200, 400, and 500 Series smoke detectors, and DH100, DH200, DH400, and DH500 Series duct smoke detectors.
|
|
|
RMK400
Data Sheet (pdf)
Installation Instructions (pdf)
The RMK400 Recessed Mounting Kit is for use with System Sensor 100, 200, 400, and 500 Series plug-in detectors.
|
|
|
SMB600
Data Sheet (pdf)
Installation Instructions (pdf)
The SMB600 flanged surface mounting kit may be used with certain System Sensor smoke detectors when flush or recessed mounting are not possible.
|
|
|
XR2
Installation Instructions (pdf)
The XR2 is an installation/removal tool for use with previous models of the 100 and 200 series plug-in smoke detectors.
Detector removal tool guide
|
|
|
BEAMMMK
Installation Instructions (pdf)
Multi-mount kit (Provides ceiling or wall mount capability with increased angular adjustment for either the beam or the reflector. When installed with the transmitter/receiver unit, BEAMSMK must be used as well)
|
|
|
6500-MMK
Installation Instructions (pdf)
Heavy duty multi-mount kit (for installations prone to vibration or where there is difficulty in maintaining the set angle. When installed with the transmitter/receiver unit, 6500-SMK must be used as well)
|
|
|
BEAMSMK
Installation Instructions (pdf)
Surface-mount kit for BEAM1224(S) and BEAM200(S) when using the BEAMMMK Multi-Mount Kit or when mounting over a recessed junction box.
|
|
|
6500-SMK
Installation Instructions (pdf)
Surface-mount kit for use with the BEAM1224 and BEAM200 when using the 6500-MMK Heavy Duty Multi-Mount Kit
|
|
|
BEAMLRK
Installation Instructions (pdf)
Long-range kit for BEAM1224 and BEAM200
|
|
|
SMK400
Data Sheet (pdf)
Installation Instructions (pdf)
The SMK400 flangeless surface mounting kit may be used with certain System Sensor smoke detectors when flush or recessed mounting are not possible.
|
|
|
BEAMHK
Installation Instructions (pdf)
Heating kit for use with the transmitter/receiver unit of System Sensor reflective projected beam smoke detectors
|
|
|
BEAMHKR
Installation Instructions (pdf)
Heating kit for use with the reflector of System Sensor reflective projected beam smoke detectors
|
|
|
CO-PLATE
Data Sheet (pdf)
Installation Instructions (pdf)
CO detector replacement plate to cover the footprint of previously installed detectors.
|
|
